Tag: qth

Already the 19th of November!

I’ve been falling behind on my updates…

(1) W4V – Veterans’ Day Special Event Station. I got a late start on Saturday… took a while to pack the truck. Setup at Fort Story took longer than expected – my biggest challenge was tying down the center mast after I’d gotten it vertical. It’s really a two person job and hard to do alone. But once I got the antenna up, the rest was easy. A beautiful day as well, low 70s and clear skies. The QSOs rolled in, as long as I was calling “CQ” I was getting QSOs. Sunday was a different story. The forecast called for rain, but I thought I could weather it out. I arrived at Fort Story but the winds became too extreme – no chance of getting the center pole up. I threw in the towel for a portable operation and headed home to operate. Not the same satisfaction running a special event from home, but I still enjoyed the QSOs. Even got Wyoming… which completes my Worked All States Award!


(2) Kenwood TS-930S…. my “new to me rig”. I picked this up from a local ham at a bargain. What a radio!

This piece of electronics perfection is over 20 years old, but it performs like a dream. The receiver is amazing. Also getting great reception reports on both SSB and CW. This rig is now the centerpiece of my shack.

(3) I didn’t work the Sweepstakes this weekend, but did have a QSO with a special event station celebrating Oklahoma statehood. However, I did work a sweepstakes station on 15M who was operating from the Santa Clara Valley.

(4) Also a few CW QSOs – I’ve hooked up my Logikey CMOS4 Keyer. Amazing little device, lots of features – but does a great job as a basic keyer.

…. but it wasn’t there!

Had a nice 80M CW QSO last night with Tony, KN4VL. There was some QSB and QRM, but we hung in there for about an hour ragchew. Tony is a retired Marine and has children and grandchildren in the armed services. I think I’m slowly making progress on the CW front.

Yesterday after work I wanted to swap out the feedline on the Carolina Windom from RG-58 to RG-8X. My plan was to lower the matching unit which has an eyelet on top that I used to raise the matching unit up to ~50ft with some heavy duty line.


I loosened the line and attempted to lower the matching unit, but the line was getting hung up in the tree branches above. I let the end of the line go and began to gently pull on the RG-58 feedline to slowly bring the matching unit down to a point where I could reach the line isolator (hanging 22′ below the matching unit) so I could swap feedlines. I got the line isolator down to my level and successfully swapped the feedlines. I then went to grab the end of the line to pull the matching unit back into the treetops, but it wasn’t there! Then I looked up. The line had been shorter than I thought – when I had pulled the matching unit down using the feedline, I had not realized that the line was so short and now the end was dangling a good 15′ above my head! I got out my ladder to try and reach the line but it wasn’t tall enough. I then tried standing on the latter with a rake, in an attempt to snag the line and pull it down. No luck. I had an idea. I grabbed one of the 10′ PVC pipes that I use for my G5RV during a portable setup to support the ends. The top of the pipe has a hole drilled through. I then grabbed about 20′ of small gauge wire, threaded a loop through the hole at the top of the pipe and then took the pole back out to the dangling line up in the air. I was able to get the end of the line through the loop, then pulled the ends of the small gauge wire tight, grabbing the line. I pulled the pipe down and the line came with it. I felt pretty stupid, but I was able to get the Carolina Windom pulled back up (now with the new feedline) and my station is up and operational.

While I think the new feedline has helped improve my signal a bit, I’m still having problems on 17M, 15M, and 12M. 17M I’ve always had issues with and from what I read, it might be an issue with the radio itself. I’m usually able to work PSK31 and Phone on 17M without the tuner, but when I dip down in the CW portion the SWR is much too high. Both 15M and 12M will not tune. Also the SWR is too high to use without the tuner. On my inverted vee, both 15M and 12M are usable. So – I know I will need to play around a bit to get everything working.

This weekend is the 2006 CQ WW DX Contest (Phone). I want to use the contest as an opportunity to complete my initial DXCC requirements. The Carolina Windom is good to go for 80M, 40M, and 20M – so I should have plenty of opportunity to work those DX stations.

At lunch today I was tuning around 20M, 17M, and 15M – lots of activity…. lots of stations testing equipment in preparation for the contest.

I need to do two things before the contest kicks off:
(1) fix the power cable to the radio. When I did some shack clean up, I moved all the equipment onto a new Alinco DM-330MVT power supply using the RigRunner. But I was having some problems with the adapter that goes on the back of the IC-706. I need to pull the power cable off, recheck the PowerPole connectors, and the four pins that connect to the IC-706.
(2) setup the ICOM CT-17 so I can save little time by having my frequency automatically saved when I log QSOs on the computer.

…. the question is – can I get both of those done before the 2000 (local) kickoff of the contest?

Sunday in the shack

I was successful in transferring the WX station duties to the computer out in the garage. I first had to get the Davis Weather Monitor II talking with the computer – which was accomplished after I changed the COM port speed to 2400 baud. I then transferred all the Weather Display files from the computer in the radio room out to the garage. The Weather Display software started up, green lights indicating that it was taking data from the Davis Weather Monitor II. But I didn’t have any sensors plugged in yet, so the only data being displayed was the indoor temp (now the garage temp) and the barometer. The outdoor temp sensor is located near the garage, so I was easily able to reroute the cable into the window of the garage and connected it to the Davis Weather Monitor II box. The outdoor temp came up right away. The next challenge was setting up the FTP for my weather webpage. The Weather Display software has great wizards that walk you through setting up different aspects of the software – the FTP setup had such a wizard. And now the webpage is getting updated every 5 minutes. Great! I still need to (1) reroute the wind direction and speed cable to the garage (requires me to get on the roof), (2) find some place to put the rain gauge (may require me to get on the roof), and (3) get the webcam hooked back up.

Spent some time cleaning up the radio room. I finally unpacked the MFJ-989C tuner that I got to go along with the Heathkit SB-220 amp. Neither are setup – that’s a project for another day.

I was also able to make contact with MI3JQD, operating from Northern Ireland… and a CW contact on 30M with John, K9??? in Indiana.

Radio Room Reconfiguration

Spent some time today reworking the shack…. still have a bit more to do.

(1) I was using two different power supplies – a PS-125 (25 amps) for the IC-706MKIIG and a different power supply for the FT-2800M (2M FM), and FT-1500M/KPC3+ (2M FM packet). I am now using the Alinco DM-330MVT (32 amps) to power the IC-706MKIIG and the FT-2800M. I’m now using the RigRunner 4010S for power distribution. I still need to make a power cable for the RigBlaster so I can get rid of the wallwart.

(2) I moved the FT-1500/KPC3+ and the other power supply out to the garage. My intent is to hook it up to the garage computer. I’ll be able to access the packet functions over the network.

(3) The weather station is down! I plan on getting that working off the garage computer as well.

(4) Heathkit SB-220 – now in the shack. But I’m still a long way from getting it operational. I need to make a list of everything I need to do to get it operational. Part of that will include putting my heavy duty MFJ tuner into action.

Saturday…..

Finally checked into the VA MARS net. The net started late and I had almost given up on it. I’m going to try and check in again tomorrow morning. I need to get around to raising the height of my inverted vee – I think it will better help my signal get out.

I was able to catch W1AA (Henry and Whitey) and their activation of the Highland Lighthouse (USA 110) out on Cape Cod. Whitey, K1VV, is usually out ever weekend doing a lighthouse activation – always has a nice signal.

Had a very nice Radio Merit Badge class for a young Scout out at Fort Monroe in the afternoon. I setup my 10′ x 10′ shelter and the ARSIB. Initially I planned on setting the G5RV (like during the W4M Memorial Day Special Event) but the wind was quite heavy, so I opted to put up the homebrew vertical dipole. To get some height on the antenna, I attached it to the top of the painter’s pole. Before I had a chance to tie down the pole, a gust of wind knocked the antenna down. The fall caused the feedline connection to break off. Not good. However, with a little bit of wire and some electrical tape, I was able to reattached the feedline connection. Now the antenna was low to the ground and I was a little concerned about it’s performance. The Scout arrived and we started reviewing the Radio Merit Badge requirements. I was able to easily tune WWV on 15 MHz and was also able to find a CW QSO in progress on 40M. Also demoed a bit of CW using my MFJ paddle that has a speaker built in. After we’d reviewed all the requirements, it was time for the HF QSO. The Scout called CQ and after a few tries, received a reply from Charlie, N1MUQ, in Stamford, CT. Charlie had a booming, solid signal and the Scout was able to successfully complete the QSO. We then moved to my mobile VHF rig and the Scout had a nice QSO with Randy, WB7URZ located up in Gloucester. Even with the antenna setup issues, the Radio Merit Badge session was a success and I think both the Scout and I had a good time.

Weekend Wrap Up

Went up to the Yorktown Battlefield Saturday and linked up with Mark, N1LO. I got to see his portable setup. He was using a delta loop antenna made of speaker wire, maybe about 25′ per side. The speaker wire was in three sections, the sections were connected using fishing line lure links. The speaker wire was terminated using banana plugs and fed into a 1:1 balun. To support the legs of the delta loop, Mark used a combination of a painter’s pole and a fiberglass fishing rod secured by a 3′ picket easily driven into the ground about 8″.


The fiberglass fishing pole’s end easily nests into the painter’s pole with about 6″ overlap raising the loop to a height of about 20′. The painter’s pole was secured to the picket using two small hose clamps. The delta loop tuned easily from 80M to 10M, but would not tune 160M. All the antenna components compacted down to fit into a plastic rifle case. Mark connected the delta loop to his IC-706MKIIG through his LDG AT-200 Pro autotuner and was easily making QSOs into Ohio (the Ohio QSO Party was underway). Power was provided by a ~100aH marine battery and a nice homebrew PowerPole distribution hub. The best part of the setup was the location – in a very nice, shady park on the southern banks of the York River.


In an endeavor to consolidate my 2M packet operations (APRS, Winlink 2K, and good ol’ fashion BBS packet) into the garage, I spent a good chunk of time pushing around boxes and crates. I purchased three 3′ high bookshelves from Target, arrayed them in an open “U” and then placed a 4’x6′ piece of plywood across the top. I filled the bookshelves with back issues of QST and equipment awaiting to be put into use. Next to this workbench, I put a previously unused, small table where I positioned my monitor and PC. I spent the late afternoon converting the PC from Ubuntu back to Window XP (… I can’t commit the time needed to tweak Unbuntu to my needs). Now I need to move the my KPC-3+ from the radio room out to the garage and see if I can get a basic packet station operational.

Also been preparing for the upcoming RV DXpedition. I’ll be taking the ARSIB along with the vertical dipole, but was also thinking about taking a G5RV. I’m also going to try and use a 75M hamstick, we’ll see how that works out.

Station Books

I want to finish up my station books tonight. I got the idea from an eHam article, but the idea behind a station book is just a consolidation of all the equipments manuals as well as a station layout diagram (to include wiring diagrams).

I’m creating a book for the main shack, the ARSIB, my Tundra mobile, and the Avalon mobile.

A few updates from the shack….

Scouts: received my Radio Merit Badge pamphlet in the mail today. Between the pamphlet and web resources, I want to put together a course package for the merit badge. One of the gentlemen I work with has a son who is interested in pursuing the Radio Merit Badge… so I need to get crackin’.

Army MARS: put in an application for Army MARS. The VA state rep told me it will be a couple weeks before I get my MARS callsign and initial training information.

US Army Amateur Radio Society: picked up a few more members. need to make contact with the Iraqi folks to check on the status of the pending YI9 applications.

DX: made contact with one of the newest DXCC entity… Montenegro! The YU6AO Montenegro DXpedition team now has a Web page at http://www.yu6ao.info/ and a log search at http://www.yu6ao.info/log.html … I’m in the log!

eBay: purchased an ASTATIC D-104 microphone. Should be a fun project adapting it for use with my IC-706MKIIG.

Local ham swap: made a deal to purchase a SB-220 Heathkit HF Linear Amplifier! This should give me a little more motivation to improve my antenna situation. Also need to acquire an antenna tuner.

Lighthouse QSL cards: finished my QSL cards for the Bodie Island Lighthouse (USA-062) and the Currituck Beach Lighthouse (USA-212) activations. Some of the Currituck Beach contacts are getting a North Carolina lighthouse key chain/compass/thermometer. Tried to get those to fellow ARLHS members.

W4M Special Event Station QSL cards/certificates: everyone who had sent me a SASE has been sent a QSL card (and certificate if they provided a large envelope).

SkyWarn Net: checked into the Chesapeake Amateur Radio Service (CARS) SkyWarn Net. They had made recent improvements to their repeater and have greatly expanded the coverage.

Ham Maps

I got one of these for the world and one for the US – great maps!

Millennia Arts’ new Ultimate DX World Map™ wall map combines contemporary cartography with updated Amateur Radio DX communication representation for a map that will look great in any setting. Extraordinary detail and quality make this an exceptional choice for reference or display, whether it’s for the ham shack or a contest.

The Ultimate DX World Map™ is a complete Mercator-style political world map. It has been designed to assist all amateur radio operators in their pursuit of DX (distance) communications. The map has been divided into CW and time zones. All countries displayed on the Ultimate DX World Map™ have their respective DX call sign prefixes. Comprehensive band plan charts for the amateur radio allocation are also conveniently located on the map for quick reference as well as other helpful frequency and communication information. In addition to being functional, the Ultimate DX World Map™ has also been designed to be aesthetically pleasing.

http://www.hammaps.com/